Leading 10 usual forklift crashes ， forklift procedure need to pay attention to these issues ！.
Leading 10 usual forklift crashes ， forklift procedure need to pay attention to these issues ！.
Blog Article
Do not undervalue the forklift at work. If the operation is not good, there will be severe crashes in mins, and there are several accidents involving forklifts.
Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift cargo surpasses the allowable width of the course and holds on the roadside shelf, which practically causes an crash.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the workers illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Case 7: The forklift motorist did not use a safety belt and fell from the vehicle when it rolled over and was crushed.
Forklift procedure ought to take note of these matters ：.
Beginning.
1. Before beginning, observe the surroundings, and after verifying that there are no obstacles that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress ( atmospheric pressure) gauge have to be risk-free before starting.
3. When the forklift starts with a tons, the driver needs to first validate that the load is steady and reputable.
4. The beginning should be slow-moving and stable.
Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not lift the fork expensive when driving. When getting in and leaving the job website or while driving, be careful that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving setting prior to driving. .
4. When transforming, if there are pedestrians or cars nearby, the driving signal must be released first. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral stability and topple. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and should keep a specific security distance from the car in front. .
7. When the forklift is running, the load needs to remain in the most affordable setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons shall not be increased except when stacking or loading. .
8. The height of the lots have to not obstruct the vehicle driver's view. In special situations, when the item affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be repaired and reported in a timely fashion, and they will certainly never run with health problems or conceal them.
filling and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique situations, safety indication must be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle need to be slow and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When utilizing a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch various other items or items. The lots should be supported with marginal back tilt of the gantry so that the Electric Forklift Truck for Warehouse tons does not glide backwards. The mast can be slanted onward slightly when the tons is decreased to allow for simple placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to pick, turn pallet discharge.
Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge Stand-on Electric Pallet Stacker the goods or reduced the fork framework.
2. Draw the emergency brake manage to dead or dispirit the emergency brake button.
3. The engine is shut off and the power is removed. (Except for special scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .
Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, check whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage should additionally be examined and the seals ought to be replaced in time.
Forklift Safety Operation Specifications.
1. You have to examine before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive across the gradient. When the slope is above 10%, the vehicle must be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia pressure to pick up the goods.
6. It is not enabled to make use of stopping force to expatriation round or easy-to-roll items.
7. It is not permitted to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of the road, the opposite side of the area with the very same size as the barrier should be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844